02
2022
-
11
Safety Performance Testing of Steel Drums for the Transport of Dangerous Goods
According to GB/T 4857.5, perform the drop test using a dedicated drop test rig. Fill the small open-top steel drum with 98% clear water, then drop it onto the weakest point along the drum's edge. After the drop, drill a hole at the highest point of the steel drum.
Dangerous chemical packaging containers include drums, cans, boxes, and more—made from a variety of materials and designs. Steel drums are the most commonly used type of packaging for hazardous chemicals. These steel drums are further categorized into closed-end steel drums and open-end steel drums.
Today, let’s talk about closed-top steel drums.
- Specification Dimensions
This test allows you to determine dimensions such as the steel drum's inner diameter, total height, lid depth, and the distance from the center of the filling port to the center of the vent hole.
- Appearance Quality
Under natural lighting, inspect the steel drum's surface, dents, weld repairs, internal quality, coating film, and zinc layer appearance using tactile methods, visual inspection, and measuring tools.
3. Quality of Closure Assembly
Ensure the sealer is fully equipped, and after assembly, verify that the surface is smooth, the seal is tight, and the top does not exceed the lip of the triple-crimped edge of the container body.
4. Coating Adhesion / Zinc Layer Thickness
If the protective coating on the inner and outer surfaces of the steel drums is applied using paint, the adhesion of the paint film must meet or exceed Grade 2 as specified in GB/T 9286. Alternatively, if galvanized steel sheets are used, the zinc coating must be at least 0.007 mm thick. Additionally, the paint film should be smooth and even, with a uniform color, free from defects such as wrinkling or sagging. The zinc layer must remain intact, with a tightly packed structure, and must not exhibit issues like delamination or blistering.
- Air-tightness test
Closed steel drums are tested according to GB/T 17344. During production, leak-testing equipment is used: compressed air is introduced into the drum to check for any leaks. Throughout the test, the drum can be rotated back and forth on a tray, allowing full visibility of the entire weld seam and crimped edge.
- Hydraulic Testing
Fill the steel drum completely with water, connect the pressure gauge to the pressurizing pump, and secure it to the filling port via a connecting component. Gradually increase the pressure inside the drum until the pressure gauge indicates the required test pressure, then stop pumping. According to standard procedures, maintain the pressure while carefully observing the drum for any signs of deformation or leakage.
- Packing Test
Steel drums should not exhibit any deformation or severe damage that could compromise their strength or lead to unstable stacking. The stacking load is applied according to the specified weight, and after maintaining this load for the required duration of the stacking test, the load is removed. The drum is then inspected for deformation and leakage.
- Drop test
According to GB/T 4857.5, conduct the drop test on a drop test rig. Fill the small open-top steel drum with 98%清水 (clear water), and drop it onto the weakest point along the drum's edge. After the drop, drill a hole at the highest point of the steel drum.
In addition to national standards, there are also several industry-specific standards available for reference when testing steel drums.
GH/T1015-1999 "Honey Packaging Steel Drums"
NY/T1131-2006 "Steel Drums for Packaging Concentrated Natural Latex"
SN/T0265-1993 "Inspection Procedure for Closed Steel Drums Used in Transport Packaging of Exported Goods"
SN/T0272-2014 "Inspection Procedure for Open-Top Steel Drums Used in Transport Packaging of Exported Goods"
SN/T3157-2012 "Inspection Procedure for Regenerated Steel Drums Used for Exporting Calcium Carbide under Container Transport Conditions" HG2823-1997 "Steel Drums for Packaging Trifluorochloromethane"
T/ZGZS 0302-2020 "Scrap Steel Drum Recycling" Testing.
undefined